fd2baac9

2.2.3. Removal and installation of the engine and transmission assembled

Removal
Remove the rechargeable battery.

Fig. 2.32. Installation of basic plugs in internal tubes of cross beams of a stretcher


Disconnect an air duct of the air filter (fig. 2.32).
Disconnect sockets of the sensor switch of lamps of a backing and plait of wires of the engine.
On models from the 5-staged manual transmission disconnect the socket of the sensor switch of lamps of a backing.
Disconnect sockets of a plait of wires of the generator.
Merge cooling liquid.

Fig. 2.33. Air duct of the air filter




NOTE
At a detachment of hoses always previously you put adjusting tags that at connection hoses were established in a starting position.

ATTENTION
Be careful at a detachment of hoses, do not spill oil or other liquid. Muffle the disconnected tubes or hoses to prevent hit of foreign particles inside.


Fig. 2.34. Detachment of the top and lower hoses of a radiator


Disconnect the top and lower hoses of a radiator from the engine, then remove a radiator assembled (fig. 2.34).
Disconnect a wire of "mass" of the engine.
Disconnect a vacuum hose of the amplifier of brakes.
Disconnect the main fuel-supply line, a hose of return of fuel and a hose of system of catching of vapors of fuel from the engine.
Disconnect both hoses (which are bringing and taking away) a heater from the engine.
Disconnect an accelerator pedal cable from the engine.
On models from the manual transmission remove a gear shifting cable from the transmission.
On models from the automatic transmission remove a cable of management of the automatic transmission from the transmission.
Disconnect a speedometer drive cable from the transmission.

Fig. 2.35. Removal of the compressor of the conditioner


Disconnect the conditioner compressor from its arm of fastening (fig. 2.35).
Poddomkratte car.

Fig. 2.36. Drain traffic jams of transmissions


Merge oil or oil for the automatic transmission (ATF) from the transmission (fig. 2.36).
Disconnect a reception pipe of system of release from a final collector.

NOTE
By means of a wire tie a reception pipe of system of release to a car body.

Fig. 2.37. Fastening of cables of the choice and gear shifting


On models remove a cable of the choice of transfers and a cable of gear shifting (fig. 2.37) from the manual transmission.

Turn off bolts of fastening of the spherical hinge of the lower lever and stabilizer to the lower lever of a suspension bracket.
Disconnect shaft of the drive of wheels from the transmission.

ATTENTION
Close openings for shaft of the drive of wheels in the transmission in order to avoid hit in dirt and foreign particles.
Before installation of shaft of the drive of wheels replace lock rings of shaft.

By means of a wire suspend the lower lever and a shaft of the drive of a wheel for a car body.
By means of chains or cables fix the engine on a traverse for arms of fastening and hang up it on the elevator. Raise the engine assembled for unloading of support of the engine from the weight of the power unit before performance of the following operations a little.

Fig. 2.38. Forward support of the engine


Remove a forward support of the engine (fig. 2.38).

Fig. 2.39. Back support of the engine


Disconnect a back support of the engine (fig. 2.39).
Turn off bolts of fastening of a side support of the engine.

Fig. 2.40. Arm of a side support


Remove an arm of a side support from the engine (fig. 2.40).
Slowly raise the engine for unloading of support from the weight of the engine and the transmission assembled and temporarily leave it in the suspended situation.

ATTENTION
Check that all cables, wires (electric sockets), hoses, etc. were disconnected from the engine.

Take caps from within an antispray guard of the left wing and turn off bolts of fastening of an arm of a support of the transmission.
Directing the power unit the transmission down, lift the engine and the transmission assembled from a motor compartment and remove them from the car.